Beef-in-sauce catering meals under blast-cooling have been investigated in a research project which aims at quantitative HACCP (hazard analysis critical control point). In view of its prospective coupling to a predictive microbiology model proposed in the project, zero-order spatial dependence has proved to suitably predict meal temperatures in response to temperature variations in the cooling air. This approach has modelled heat transfer rates via the a priori unknown convective coefficient hc which is allowed to vary due to uncertainty and variability in the actual modus operandi of the chosen case study hospital kitchen. Implemented in MS Excel®, the numerical procedure has successfully combined the 4
th order Runge-Kutta method, to solve the governing equation, with non-linear optimization, via the built-in Solver, to determine the coefficient hc. In this work, the coefficient hc was assessed for 119 distinct recently-cooked meal samples whose temperature-time profiles were recorded in situ after 17 technical visits to the hospital kitchen over a year. The average value and standard deviation results were hc = 12.0 ± 4.1 W m−2 K −1 , whilst the lowest values (associated with the worst cooling scenarios) were about hc ≈ 6.0 W m−2 K −1 .Convective heat transfer

The regulation of a profession is justified when it improves consumer protection and public health. Higher education food science and technology (FST) degrees, widely offered in many universities in Europe open to a wide range of jobs in the food sectors where the employees could cover different positions, roles and carry out diverse activities dealing with the food production and the quality and safety of the food products.This work reviews the state of the art of the FST regulated professions requiring higher education qualifications in the European countries. The research was carried out by collecting specific information on regulated professions by contacting unions, professional associations, public servant categories/professions, and by visiting national and EU websites.  The data collected for each regulated profession were: country, training/education required, date of implementation of regulation, professional training (if required), capability test (if required) and acts required by law to be signed by a regulated professional. Only professions that required a higher education diploma were included in this search.Few countries were found to have a regulated profession in FST, in particular: Food Engineering (Turkey), Food Technologist (Greece, Iceland, Italy and Slovenia), and Oenologist (Italy, Portugal and Spain). FST regulated professions in Europe are thus scarce and have a rather limited history. The Food Technologist in Italy and the Food Engineer in Turkey were found to be the only completely regulated professions found in Europe. Food and professional regulation have been evolved over the years and raised the debate on the regulation of FST professions. Academia as well as other policymakers has to further contribute to this discussion to keep high the standards for quality of education and training of the qualified workforce and professionals in the food sector.

The paper gives a brief overview of the current nutritional status of the Ukrainian population and describes useful buckwheat properties. The objective of the paper is to study the effect of buckwheat processing products (flour and flakes) on the technological process and quality of bread made from whole-wheat flour. This paper describes and analyzes research data on the rheological properties of dough samples which were determined by farinograph and amylograph.Investigation of structural and mechanical properties of dough showed an increase in water-absorbing capacity in all samples when adding buckwheat products. Moreover, dough made with buckwheat flakes has a lower value of mixing tolerance index (by 47 %) than dough made from buckwheat flour, and a higher valorimetric value (by 20 %). Determination of dough properties by amylogram has shown that a sample containing buckwheat flakes has a higher maximum viscosity than a sample containing buckwheat flour. Determination of the gas-production and gas-retention capacity of dough is also presented, along with an analysis of the quality of finished products based on the results of laboratory baking tests.The samples of bread supplemented with buckwheat flakes have better shape stability (by 21 %), specific volume (by 12 %) and porosity (by 11 %) than bread made from buckwheat flour. The organoleptic evaluation of finished product quality has shown that bread supplemented with buckwheat flakes has a more fluffy-texture, elastic crumb and uniform porosity than bread made from buckwheat flour. Buckwheat flakes proved to have a better effect on parameters of the technological process and quality of bread when compared with buckwheat flour.

The so-called vegetable milks are in the spotlight thanks to their lactose-free, animal protein-free and cholesterol-free features which fit well with the current demand for healthy food products. Nevertheless, and with the exception of soya, little information is available about these types of milks and their derivatives. The aims of this review, therefore, are to: highlight the main nutritional benefits of the nut and cereal vegetable milks available on the market, fermented or not; describe the basic processing steps involved in their manufacturing process; and analyze the major problems affecting their overall quality, together with the current feasible solutions. On the basis of the information gathered, vegetable milks and their derivatives have excellent nutritional properties which provide them a high potential and positive market expectation. Nevertheless, optimal processing conditions for each raw material or the application of new technologies have to be researched in order to improve the quality of the products. Hence, further studies need to be developed to ensure the physical stability of the products throughout their whole shelf-life. These studies would also allow for a reduction in the amount of additives (hydrocolloids and/or emulsifiers) and thus reduce the cost of the products. In the particular case of fermented products, the use of starters which are able to both improve the quality (by synthesizing enhanced flavors and providing optimal textures) and exert health benefits for consumers (i.e. probiotics) is the main challenge to be faced in future studies.